Tag Archives: FAME.

1237-1246 K. Sirviö, S. Heikkilä, R. Help, S. Niemi and E. Hiltunen
Properties of local produced animal-fat based biodiesel and its blend with fossil fuel
Abstract |
Full text PDF (638 KB)

Properties of local produced animal-fat based biodiesel and its blend with fossil fuel

K. Sirviö*, S. Heikkilä, R. Help, S. Niemi and E. Hiltunen

University of Vaasa, Faculty of Technology, PL 700, FIN-65101 Vaasa, Finland
*Correspondence: katriina.sirvio@uva.fi

Abstract:

In the near future, more emphasis must be put on reducing greenhouse gas (GHG) emissions in road transportation, house heating, agricultural activities, marine transport etc. This study concentrated on the use of alternative fuels in engine-driven applications of non-road machineries and decentralized energy production. Today, the engines are mainly designed for crude oil derived fuels and liquid renewable fuels are blended with crude oil based fuels to fulfill the requirements of renewable energy usage. Due to the environmental reasons on one hand and to the agricultural needs, on the other hand, different blends of bio- and fossil fuels are becoming more popular. In Europe, the maximum FAME content in diesel fuel is 7 vol% according to the EN 590:2013 but higher percentages are also available and targeted around the world. For example in the United States, the 20% blend fraction is becoming more common. For these reasons, B20 fuels were chosen to be investigated in this study. Special emphasis was put on improving blending issues since fuel blending may cause some operating risks. The main aim was to research widely the properties of animal-fat based methyl ester (AFME) and B20 fuel blend produced from it. AFME is a waste based fuel and produced in Ostrobothnia region, Finland. The aim was to find out in which engine applications the fuels are feasible and investigate if the fuels fit in the quality of automotive fuel Standards. According to the results, AFME is a feasible option to increase self-sufficient energy production in Ostrobothnia.

Key words:

, , , , ,




1232–1241 K. Sirviö, S. Niemi, S. Heikkilä and E. Hiltunen
Effects of sulphur on the storage stability of the bio and fossil fuel blends
Abstract |
Full text PDF (371 KB)

Effects of sulphur on the storage stability of the bio and fossil fuel blends

K. Sirviö*, S. Niemi, S. Heikkilä and E. Hiltunen

University of Vaasa, Faculty of Technology, PL 700, FIN-65101 Vaasa, Finland
*Correspondence: katriina.sirvio@uva.fi

Abstract:

In this study, the aim was to find out if mixing two common fuels together could be beneficial for both the environment and storage stability of fuel. It is obvious, that adding biodiesel to fossil fuel will decrease its sulphur content and reduce its carbon monoxide and hydrocarbon, sulphur dioxide and soot emissions. But will the high sulphur content enhance the storage stability of the biodiesel? Four B20 samples were produced, consisting of 20 vol% biodiesel and 80 vol% fossil diesel. The samples were prepared from rapeseed methyl ester (RME), low sulphuric fossil diesel fuel and high sulphuric diesel solvent. The blends had different sulphur contents of 6, 76, 149 and 226 mg kg-1. For these B20 fuel samples, the parameters were compared that correlate with the storage stability of the fuel blends. The studied parameters were the oxidation stability (OSI, according to EN 15751:2015), acid number (AN, according to EN 14104:2003) and kinematic viscosity (KV, by Stabinger SVM 3000 rotational viscometer). The measurements were carried out straight after mixing the blends, and again after 4, 8 and 12 weeks. According to the results, the fuel containing less sulphur slightly lost its oxidation stability within three months. Instead, the oxidation stability of high sulphuric samples improved within the same time frame. As a conclusion, the study gave a reason to assume that – in spite of its known drawbacks – the sulphur may be favourable to fuel blends’ storage stability but the phenomenon and chemistry should be studied in more detail.

Key words:

, , , , , ,




244–250 K. Sirviö, S. Niemi, S. Heikkilä and E. Hiltunen
The effect of sulphur content on B20 fuel stabil
Abstract |
Full text PDF (266 KB)

The effect of sulphur content on B20 fuel stabil

K. Sirviö*, S. Niemi, S. Heikkilä and E. Hiltunen

University of Vaasa, Faculty of Technology, PL 700, FIN-65101 Vaasa, Finland
*Correspondence: katriina.sirvio@uva.fi

Abstract:

The aim of this study was to investigate if a high amount of sulphur is favourable for the fuel blends’ storage stability. The parameters that correlate with the storage stability of the fuel blends were compared with two B20 fuel samples consisting of 20 vol% biodiesel and 80 vol% fossil diesel. The studied parameters were the oxidation stability (OSI), acid number and kinematic viscosity. The measurements were carried out straight after mixing the blends, and again after 4 and 9 weeks. One of the B20 samples was prepared from rapeseed methyl ester (RME) and fossil diesel fuel containing 6.6 mg kg-1 sulphur and the other from the same RME but the fossil diesel fuel contained 186 mg kg-1 of sulphur. According to the results of this study, the fuel containing less sulphur had slightly better quality during the entire study. Though, the OSI of the fuel containing more sulphur decreased less in percentages than it did for the fuel containing less sulphur. As a conclusion, the study gives a reason to assume that the sulphur may be favourable to fuel blends’ storage stability but it should be studied for a longer time to confirm this statement. 

Key words:

, , , , ,




541-549 J. Čedík,, M. Pexa, J. Mařík, V. Hönig, Š. Horníčková and K. Kubín
Influence of butanol and FAME blends on operational characteristics of compression ignition engine
Abstract |
Full text PDF (851 KB)

Influence of butanol and FAME blends on operational characteristics of compression ignition engine

J. Čedík¹,*, M. Pexa¹, J. Mařík¹, V. Hönig², Š. Horníčková² and K. Kubín³

¹Czech University of Life Sciences Prague, Faculty of Engineering, Department for Quality and Dependability of Machines, Kamýcká 129, CZ16521 Prague 6, Czech Republic; *Correspondence cedikj@tf.czu.cz
²Czech University of Life Sciences Prague, Faculty of Agrobiology, Food and Natural Resources, Department of Chemistry, Kamýcká 129, CZ16521 Prague 6, Czech Republic
³Research Institute of Agricultural Engineering, p.r.i., Drnovská 507, CZ16101 Prague 6, Czech Republic

Abstract:

The issue of the use of alternative fuels in diesel engines is discussed in this paper. The purpose is to reduce the dependence of EU Member States on fuels of petroleum origin. One of the possibilities is the use of butanol produced from organic products. The use of pure butanol in diesel engines is not possible. However, it may be used as an additive for fuels of petroleum origin or adding to oil for improving the operating conditions of the engine. Successively 10, 30 and 50% n-butanol was used as an additive. Turbocharged combustion engine of the tractor Zetor 8641 Foretrra was used to the test. This engine was burdened using a dynamometer to the PTO. Performance parameters and fuel consumption of the engine were monitored during measurements. Performance parameters of the engine decreases and fuel consumption increases due to the properties of butanol. Cleansing properties of butanol which restrict carbonization on functional surfaces of the engine seems advantageous.

Key words:

, , , , ,




541-549 J. Čedík,, M. Pexa, J. Mařík, V. Hönig, Š. Horníčková and K. Kubín
Influence of butanol and FAME blends on operational characteristics of compression ignition engine
Abstract |
Full text PDF (851 KB)

Influence of butanol and FAME blends on operational characteristics of compression ignition engine

J. Čedík¹,*, M. Pexa¹, J. Mařík¹, V. Hönig², Š. Horníčková² and K. Kubín³

¹Czech University of Life Sciences Prague, Faculty of Engineering, Department for Quality and Dependability of Machines, Kamýcká 129, CZ16521 Prague 6, Czech Republic; *Correspondence cedikj@tf.czu.cz
²Czech University of Life Sciences Prague, Faculty of Agrobiology, Food and Natural Resources, Department of Chemistry, Kamýcká 129, CZ16521 Prague 6, Czech Republic
³Research Institute of Agricultural Engineering, p.r.i., Drnovská 507, CZ16101 Prague 6, Czech Republic

Abstract:

The issue of the use of alternative fuels in diesel engines is discussed in this paper. The purpose is to reduce the dependence of EU Member States on fuels of petroleum origin. One of the possibilities is the use of butanol produced from organic products. The use of pure butanol in diesel engines is not possible. However, it may be used as an additive for fuels of petroleum origin or adding to oil for improving the operating conditions of the engine. Successively 10, 30 and 50% n-butanol was used as an additive. Turbocharged combustion engine of the tractor Zetor 8641 Foretrra was used to the test. This engine was burdened using a dynamometer to the PTO. Performance parameters and fuel consumption of the engine were monitored during measurements. Performance parameters of the engine decreases and fuel consumption increases due to the properties of butanol. Cleansing properties of butanol which restrict carbonization on functional surfaces of the engine seems advantageous.

Key words:

, , , , ,